Computer Acronyms

Computer Acronyms


ADSL - Asymmetric Digital Subscriber Line
AGP - Accelerated Graphics Port
ALI - Acer Labs, Incorporated
ALU - Arithmetic Logic Unit
AMD - Advanced Micro Devices
APC - American Power Conversion
ASCII - American Standard Code for Information Interchange
ASIC - Application Specific Integrated Circuit
ASPI - Advanced SCSI Programming Interface
AT - Advanced Technology
ATI - ATI Technologies Inc.
ATX - Advanced Technology Extended


--- B ---
BFG - BFG Technologies
BIOS - Basic Input Output System
BNC - Barrel Nut Connector


--- C ---
CAS - Column Address Signal
CD - Compact Disk
CDR - Compact Disk Recorder
CDRW - Compact Disk Re-Writer
CD-ROM - Compact Disk - Read Only Memory
CFM - Cubic Feet per Minute (ft�/min)
CMOS - Complementary Metal Oxide Semiconductor
CPU - Central Processing Unit
CTX - CTX Technology Corporation (Commited to Excellence)


--- D ---


DDR - Double Data Rate
DDR-SDRAM - Double Data Rate - Synchronous Dynamic Random Access Memory
DFI - DFI Inc. (Design for Innovation)
DIMM - Dual Inline Memory Module
DRAM - Dynamic Random Access Memory
DPI - Dots Per Inch
DSL - See ASDL
DVD - Digital Versatile Disc
DVD-RAM - Digital Versatile Disk - Random Access Memory


--- E ---
ECC - Error Correction Code
ECS - Elitegroup Computer Systems
EDO - Extended Data Out
EEPROM - Electrically Erasable Programmable Read-Only Memory
EPROM - Erasable Programmable Read-Only Memory
EVGA - EVGA Corporation


--- F ---
FC-PGA - Flip Chip Pin Grid Array
FDC - Floppy Disk Controller
FDD - Floppy Disk Drive
FPS - Frame Per Second
FPU - Floating Point Unit
FSAA - Full Screen Anti-Aliasing
FS - For Sale
FSB - Front Side Bus


--- G ---
GB - Gigabytes
GBps - Gigabytes per second or Gigabits per second
GDI - Graphical Device Interface
GHz - GigaHertz


--- H ---
HDD - Hard Disk Drive
HIS - Hightech Information System Limited
HP - Hewlett-Packard Development Company
HSF - Heatsink-Fan


--- I ---
IBM - International Business Machines Corporation
IC - Integrated Circuit
IDE - Integrated Drive Electronics
IFS- Item for Sale
IRQ - Interrupt Request
ISA - Industry Standard Architecture
ISO - International Standards Organization


--- J ---
JBL - JBL (Jame B. Lansing) Speakers
JVC - JVC Company of America


- K ---
Kbps - Kilobits Per Second
KBps - KiloBytes per second


--- L ---
LG - LG Electronics
LAN - Local Area Network
LCD - Liquid Crystal Display
LDT - Lightning Data Transport
LED - Light Emitting Diode


--- M ---
MAC - Media Access Control
MB � MotherBoard or Megabyte
MBps - Megabytes Per Second
Mbps - Megabits Per Second or Megabits Per Second
MHz - MegaHertz
MIPS - Million Instructions Per Second
MMX - Multi-Media Extensions
MSI - Micro Star International


--- N ---
NAS - Network Attached Storage
NAT - Network Address Translation
NEC - NEC Corporation
NIC - Network Interface Card


--- O ---
OC - Overclock (Over Clock)
OCZ - OCZ Technology
OEM - Original Equipment Manufacturer


--- P ---
PC - Personal Computer
PCB - Printed Circuit Board
PCI - Peripheral Component Interconnect
PDA - Personal Digital Assistant
PCMCIA - Peripheral Component Microchannel Interconnect Architecture
PGA - Professional Graphics Array
PLD - Programmable Logic Device
PM - Private Message / Private Messaging
PnP - Plug 'n Play
PNY - PNY Technology
POST - Power On Self Test
PPPoA - Point-to-Point Protocol over ATM
PPPoE - Point-to-Point Protocol over Ethernet
PQI - PQI Corporation
PSU - Power Supply Unit


--- R ---
RAID - Redundant Array of Inexpensive Disks
RAM - Random Access Memory
RAMDAC - Random Access Memory Digital Analog Convertor
RDRAM - Rambus Dynamic Random Access Memory
ROM - Read Only Memory
RPM - Revolutions Per Minute


--- S ---
SASID - Self-scanned Amorphous Silicon Integrated Display
SCA - SCSI Configured Automatically
SCSI - Small Computer System Interface
SDRAM - Synchronous Dynamic Random Access Memory
SECC - Single Edge Contact Connector
SODIMM - Small Outline Dual Inline Memory Module
SPARC - Scalable Processor ArChitecture
SOHO - Small Office Home Office
SRAM - Static Random Access Memory
SSE - Streaming SIMD Extensions
SVGA - Super Video Graphics Array
S/PDIF - Sony/Philips Digital Interface


--- T ---
TB - Terabytes
TBps - Terabytes per second
Tbps - Terabits per second
TDK - TDK Electronics
TEC - Thermoelectric Cooler
TPC - TipidPC
TWAIN - Technology Without An Important Name


--- U ---
UART - Universal Asynchronous Receiver/Transmitter
USB - Universal Serial Bus
UTP - Unshieled Twisted Pair


--- V ---
VCD - Video CD
VPN - Virtual Private Network


--- W ---
WAN - Wide Area Network
WTB - Want to Buy
WYSIWYG - What You See Is What You Get


--- X ---
XGA - Extended Graphics Array
XFX - XFX Graphics, a Division of Pine
XMS - Extended Memory Specification
XT - Extended Technology

Check to see if you are infected from internet

Check to see if you are infected in windows XP from internet

When you first turn on you computer (BEFORE DIALING INTO YOUR ISP),
open a MS-DOS Prompt window (start/programs MS-DOS Prompt).
Then type netstat -arn and press the Enter key.
Your screen should display the following (without the dotted lines
which I added for clarification).

-----------------------------------------------------------------------------
Active Routes:

  Network Address          Netmask  Gateway Address        Interface  Metric
        127.0.0.0        255.0.0.0        127.0.0.1        127.0.0.1      1
  255.255.255.255  255.255.255.255  255.255.255.255          0.0.0.0      1

Route Table

Active Connections

  Proto  Local Address          Foreign Address        State

--------------------------------------------------------------------------------

If you see anything else, there might be a problem (more on that later).
Now dial into your ISP, once you are connected;
go back to the MS-DOS Prompt and run the same command as before
netstat -arn, this time it will look similar to the following (without
dotted lines).

-------------------------------------------------------------------------------------

Active Routes:

  Network Address          Netmask  Gateway Address        Interface  Metric
          0.0.0.0          0.0.0.0    216.1.104.70    216.1.104.70      1
        127.0.0.0        255.0.0.0        127.0.0.1        127.0.0.1      1
      216.1.104.0    255.255.255.0    216.1.104.70    216.1.104.70      1
    216.1.104.70  255.255.255.255        127.0.0.1        127.0.0.1      1
    216.1.104.255  255.255.255.255    216.1.104.70    216.1.104.70      1
        224.0.0.0        224.0.0.0    216.1.104.70    216.1.104.70      1
  255.255.255.255  255.255.255.255    216.1.104.70    216.1.104.70      1

Route Table

Active Connections

  Proto  Local Address          Foreign Address        State
  TCP    0.0.0.0:0              0.0.0.0:0              LISTENING
  TCP    216.1.104.70:137      0.0.0.0:0              LISTENING
  TCP    216.1.104.70:138      0.0.0.0:0              LISTENING
  TCP    216.1.104.70:139      0.0.0.0:0              LISTENING
  UDP    216.1.104.70:137      *:*      

--------------------------------------------------------------------------------

What you are seeing in the first section (Active Routes) under the heading of
Network Address are some additional lines. The only ones that should be there
are ones belonging to your ISP (more on that later). In the second section
(Route Table) under Local Address you are seeing the IP address that your ISP
assigned you (in this example 216.1.104.70).

The numbers are divided into four dot notations, the first three should be
the same for both sets, while in this case the .70 is the unique number
assigned for THIS session. Next time you dial in that number will more than
likely be different.

To make sure that the first three notation are as they should be, we will run
one more command from the MS-DOS window.
From the MS-DOS Prompt type tracert /www.yourispwebsite.com or .net
or whatever it ends in. Following is an example of the output you should see.

---------------------------------------------------------------------------------------

Tracing route to /www.motion.net [207.239.117.112]over a maximum of 30 hops:
1  128 ms  2084 ms  102 ms  chat-port.motion.net [216.1.104.4]
2  115 ms  188 ms  117 ms  chat-core.motion.net [216.1.104.1]
3  108 ms  116 ms  119 ms  www.motion.net [207.239.117.112]
Trace complete.

------------------------------------------------------------------------------------------

You will see that on lines with the 1 and 2 the first three notations of the
address match with what we saw above, which is a good thing. If it does not,
then some further investigation is needed.

If everything matches like above, you can almost breath easier. Another thing
which should you should check is programs launched during startup. To find
these, Click start/programs/startup, look at what shows up. You should be
able to recognize everything there, if not, once again more investigation is
needed.

-------------------------------------------------------------------------------------------

Now just because everything reported out like we expected (and demonstrated
above) we still are not out of the woods. How is this so, you ask? Do you use
Netmeeting? Do you get on IRC (Internet Relay Chat)? Or any other program
that makes use of the Internet. Have you every recieved an email with an
attachment that ended in .exe? The list goes on and on, basically anything
that you run could have become infected with a trojan. What this means, is
the program appears to do what you expect, but also does just a little more.
This little more could be blasting ebay.com or one of the other sites that
CNNlive was talking about.

What can you do? Well some anti-virus software will detect some trojans.
Another (tedious) thing is to start each of these "extra" Internet programs
one at a time and go through the last two steps above, looking at the routes
and connection the program uses. However, the tricky part will be figuring
out where to tracert to in order to find out if the addresses you see in
step 2 are "safe" or not. I should forewarn you, that running tracert after
tracert, after tracert might be considered "improper" by your ISP. The steps
outlined above may not work exactly as I have stated depending upon your ISP,
but with a true ISP it should work. Finally, this advise comes with NO
warranty and by following my "hints' you implicitly release me from ANY and
ALL liability which you may incur.


 Other options

Display protocol statistics and current TCP/IP network connections.
Netstat [-a] [-e] [-n] [-s] [-p proto] [-r] [intervals]

-a.. Display all connections and listening ports.
-e.. Display Ethernet statistics. This may be combined with the -s option.
-n.. Diplays address and port numbers in the numerical form.
-p proto..Shows connections for the protocol specified by proto; proto may be
TCP or UDP. If used with the -s option to display per-protocol statistics,
proto may be TCP, UDP, of IP.
-r.. Display the routing table.
-s.. Display per-protocol statistics. By default, statistics are shown for TCP
UDP and IP; the -p option may be used to specify a subset of the default
interval..Redisplay selected statistics, pausing intervals seconds between each
display. If omitted. netstat will print the current configuration information
once

How To: Change Your Ip In Less Then 1 Minute in XP

How To: Change Your Ip In Less Then 1 Minute in XP

1. Click on "Start" in the bottom left hand corner of screen
2. Click on "Run"
3. Type in "command" and hit ok

You should now be at an MSDOS prompt screen.

4. Type "ipconfig /release" just like that, and hit "enter"
5. Type "exit" and leave the prompt
6. Right-click on "Network Places" or "My Network Places" on your desktop.
7. Click on "properties"

You should now be on a screen with something titled "Local Area Connection", or something close to that, and, if you have a network hooked up, all of your other networks.

8. Right click on "Local Area Connection" and click "properties"
9. Double-click on the "Internet Protocol (TCP/IP)" from the list under the "General" tab
10. Click on "Use the following IP address" under the "General" tab
11. Create an IP address (It doesn't matter what it is. I just type 1 and 2 until i fill the area up).
12. Press "Tab" and it should automatically fill in the "Subnet Mask" section with default numbers.
13. Hit the "Ok" button here
14. Hit the "Ok" button again

You should now be back to the "Local Area Connection" screen.

15. Right-click back on "Local Area Connection" and go to properties again.
16. Go back to the "TCP/IP" settings
17. This time, select "Obtain an IP address automatically"
tongue.gif 18. Hit "Ok"
19. Hit "Ok" again
20. You now have a new IP address

With a little practice, you can easily get this process down to 15 seconds.

P.S:
This only changes your dynamic IP address, not your ISP/IP address. If you plan on hacking a website with this trick be extremely careful, because if they try a little, they can trace it back

Change the location of My Documents folder in XP

Change the location of My Documents folder in XP

I just found out about this today, and I use Windows XP for some time now, so i guess there are others out there who don't know about this yet.

But normally windows saves the "My Documents" folder on your C-drive.
But when you right-click on it and go to properties, you can change the location where you want windows to save your Documents folder.
I have a partition set up with just windows on it, and all my things i want to keep are on different partitions/disks. So now I put My Documents on another partition than where I have windows installed. If windows screws up and you have to format your C-drive again, your documents will be spared at least...

Change the default location of installation drive

Change the default location of installation drive

As the size of hardrives increase, more people are using partitions to seperate and store groups of files.

XP uses the C:\Program Files directory as the default base directory into which new programs are installed. However, you can change the default installation drive and/ or directory by using a Registry hack.

Run the Registry Editor (regedit)and go to

HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion

Look for the value named ProgramFilesDir. by default,this value will be C:\Program Files. Edit the value to any valid drive or folder and XP will use that new location as the default installation directory for new programs.